中文字幕一区二区久久人妻网站,高清精品久久国产免费,蜜桃福利在线观看视频,黄片一级女和女

釀酒設備處理停機的正確方法?

發布于:2021-10-18 11:38:05  來源:http://m.credicard.com.cn

在使用釀酒設備的時候,如果釀酒設備有停機故障,你一定不要驚慌,這其實是很多設備使用中會常見的一些問題,下面讓小編來告訴你可以這樣做。
When using the brewing equipment, you must not panic if the brewing equipment has shutdown failure. This is actually some common problems in the use of many equipment. Let me tell you this.
1.立即關閉釀酒設備的料斗門,盡可能擠出桶內多余的物料;切斷電源和水源,取下模具上的加熱元件,然后取下模具,然后用專用工具取下螺釘。如果要生產聚烯烴材料,不得拆卸螺釘。但是,如果出現嚴重的機械故障,一般很難在短時間內恢復生產,將螺釘取出進行清洗。
1. Immediately close the hopper door of the brewing equipment and squeeze out the excess materials in the barrel as much as possible; Cut off the power and water supply, first remove the heating element on the die, then remove the die, and then remove the screw with a special tool. If polyolefin material is to be produced, the screws must not be removed. However, in case of serious mechanical failure, it is generally difficult to resume production in a short time. Take out the screws for cleaning.
2.用銅或鋁工具清洗螺桿、機筒和模具,并仔細檢查零件表面是否有磨損和傷痕。如果有的話,用油石仔細打磨。釀酒設備安裝模具的壓蓋也應仔細打磨。
2. Clean the screw, barrel and die with copper or aluminum tools, and carefully check whether there are wear and scars on the surface of parts. If any, polish it carefully with an oilstone. The gland of the installation mould of brewing equipment shall also be carefully polished.
3.如果釀酒設備按上述方法清理后沒有啟動,檢查臨時停機的原因。如果不能立即恢復生產,應先用油脂垂直懸掛螺釘,然后再安排故障排除和維修。設備修補后,重新安裝螺桿,在用于安裝模具的螺栓上涂抹耐高溫油脂,然后安裝模具。螺栓應該對角擰緊。如果條件允許,使用扭矩扳手,以確保模具不會泄漏,并且再次拆卸非常方便。
3. If the brewing equipment is not started after cleaning according to the above methods, first check the causes of temporary shutdown. If production cannot be resumed immediately, hang the screws vertically with grease first, and then arrange troubleshooting and maintenance. After the equipment is repaired, reinstall the screw, apply high-temperature grease on the bolts used to install the mold, and then install the mold. Bolts should be tightened diagonally. If conditions permit, use a torque wrench to ensure that the die will not leak and it is very convenient to disassemble again.
4.由于釀酒過程沒有得到很好的控制,因此有必要找出釀酒設備操作過程失控的原因并加以。例如,是因?yàn)闇囟瓤刂苾x表出了故障還是熱電偶沒有正確插入。
4. Because the brewing process is not well controlled, it is necessary to find out the causes of out of control in the operation process of brewing equipment and solve them. For example, is it because the temperature control instrument fails or the thermocouple is not inserted correctly.
以上就是釀酒設備停機時我們應該做的。正確的預防和有用的維護是提高釀酒設備使用效率的基本保證。對于釀酒設備的突然關機,雖然出現不多,但也不能忽視。
The above is what we should do when the brewing equipment is shut down. Correct prevention and useful maintenance are the basic guarantee to improve the use efficiency of brewing equipment. The sudden shutdown of brewing equipment is rare, but it can not be ignored.

咨詢熱線:
0537-4556677

亚洲精品中文字幕无码不卡18禁| 欧美一直看黄片| 大香蕉国语视频在线| 可以看黄色小说的视频网站| 嗯啊好爽视频干| 西班牙无码一区| 韩国无码网| 天堂久久久久久久久久久久久久久 | 色欲porn| 探花最新免费网址| 吃瓜AV无码一区二区| 少妇内射在线| 开心五月一区二区| 在线播放| 自拍偷拍大图国产| 久久久久综合网88| 日本免费中文字幕精品发布| 欧美图一区二区三区| 内射日本老熟女| 上海午夜福利| 欧美日韩性xxx| 3P刮伦视频| 亚洲日韩久久日韩| 大香蕉蕉伊| 激情 骚逼 操逼| 美女黄频在线看| 国产区尤物| 国产精品欧美麻豆玖壹壹区二区| 手机看片日韩黑人欧美| 欧美国产日本久久久久| 乱码1区2区3区产品精品| 日本久久一区电影| 欧美日韩国产一区二区二不卡| 少妇精品高潮一区二区三区| 青青草视频精品久久| 日韩AV一区二区加勒比| 国产传媒最新avww| 欧美国产肛交| 色狠狠AV北条麻妃| 狠狠做欧美| 一本在线不卡视频|